How to Rebuild the Entire Front Suspension in your Car or Truck

  • нийтэлсэн 13 өдрийн өмнө

    ChrisFixChrisFix

    Үргэлжлэх хугацаа: 23:17

    Learn how to replace the ENTIRE front suspension of your car in this two episode series. First I will show you how to remove the wheel bearing, ball joints, control arms, tie rod, strut, and axle.
    The ball joint and wheel bearing has to be pressed out of the knuckle and I have a bunch of tips and tricks to make that easy. The upper control arm ball joint and tie rod can get stuck in the knuckle so I show some tricks on how to easily remove that. The rest of the suspension parts are pretty simple to remove and replace.
    NEXT EPISODE: mnfilm.net/v-%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-V_g1-WHD4rw.html
    Tools and Products:
    Mevotech Suspension Parts: amzn.to/2VKrmfr
    Rust Paint: amzn.to/2Dg5yAV
    Impact gun: amzn.to/2It3KIo
    Torque Wrench: amzn.to/2UO2yFY
    Bearing Press: amzn.to/2Gh8tv3
    Ball Joint Puller: amzn.to/2P2wmcH
    Slide Hammer: amzn.to/2URoqAe
    Ball Joint Press: amzn.to/2UTxEvR
    4lb Hammer: amzn.to/2GhZ06A
    Vice: amzn.to/2IfqPyV
    → Become a ChrisFix Subscriber: mnfilm.net/us/paintballoo7
    → Instagram: instagram.com/chrisfixit
    → Facebook: facebook.com/chrisfix8
    → Website: www.ChrisFixed.com
    → My Channel Home Page: mnfilm.net/us/ChrisFix
    **If the video was helpful, remember to give it a "thumbs up" and consider subscribing.**
    Disclaimer:
    Due to factors beyond the control of ChrisFix, I cannot guarantee against improper use or unauthorized modifications of this information. ChrisFix assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. ChrisFix recommends safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of ChrisFix, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not ChrisFix.

ChrisFix
ChrisFix

Did you guys get notified by YouTube that the video was posted? Also when you watched the video, was there a screen that said "this video was flagged by the YouTube community and may be offensive" or something like that? Just wanted to check because I had issues last night which is why I had to postpone publishing the video. I hope it's all fixed and you guys learn a lot from the video! Stay tuned for the next video and then for a video that, well, covers a life changing event ;) Also for those asking why I am wondering, here is what happened last night when I went to publish: https://www.instagram.com/p/BwI-VOhFkt2/

13 өдрийн өмнө
John B
John B

ChrisFix what kind of pry bar is the curved one?

7 цагийн өмнө
Logan Farmer
Logan Farmer

ChrisFix im a fan I been your videos for 10 yers and my dad is beying a car for me and im 11 yeres old omost 12 yeres old. Reply plez

8 цагийн өмнө
Lurking Shadow
Lurking Shadow

Where did you find the steering and suspension kit I would to do the same for my car

3 өдрийн өмнө
Its Dudster
Its Dudster

Its fixed

4 өдрийн өмнө
UdaMesican
UdaMesican

No I was not notified, glad to see it though this is going to be an upcoming project!

4 өдрийн өмнө
The AgentZero
The AgentZero

Did you paint the axle or did you get a new one?

Цагийн өмнө
David Macnamara
David Macnamara

hey chris fix i have a toyota starlet EP91 im doing a project on, where do you find new parts for old cars before 2000

2 цагийн өмнө
NO NAME
NO NAME

7:03 is funny get it??

8 цагийн өмнө
policewannabe
policewannabe

The 790 dislikes had no suspension, it rusted out.

8 цагийн өмнө
Bartłomiej Z
Bartłomiej Z

Dude I love your videos, greatly appreciated ^^

10 цагийн өмнө
QuickFix Autos
QuickFix Autos

Hi Chris amazing video! I love watching your useful videos you have encouraged me to make my own videos

13 цагийн өмнө
os Pe
os Pe

I dont even have a car cuz im 15 I wont change any suspensions ever probably but i still watch every video

14 цагийн өмнө
ts46176
ts46176

Are you allowed to work on cars at your house, or will you get in trouble?

15 цагийн өмнө
Ricardo Martinho
Ricardo Martinho

Top obrigado

18 цагийн өмнө
ANTOMCDAID Vlog05
ANTOMCDAID Vlog05

Yes plz make more del sol vids

19 цагийн өмнө
Sup Dude
Sup Dude

7:04 Very wrong

21 цагийн өмнө
Sup Dude
Sup Dude

Im to young to have a car

21 цагийн өмнө
Sup Dude
Sup Dude

Im oyou to havea car

21 цагийн өмнө
cresendiz94
cresendiz94

What is your opinion on Medtech? Everything i read are back and forward. But most say they are lower grade parts.

23 цагийн өмнө
Meinalyn Lopez
Meinalyn Lopez

But Chris fix i don't know how to install a role cage and a turbo/supercharger but I already install a vinyl at my drag racing car Porsche carra ft

Өдрийн өмнө
Meinalyn Lopez
Meinalyn Lopez

Chris fix why do you post videos so long??

Өдрийн өмнө
Emperor Steel
Emperor Steel

I'll be those typical people who praise something that's good, but I am not gonna lie, this is a very informative video. I want to get into auto repair. So thank you Chris for sharing your knowledge of vehicles with us. I don't need a suspension replacement now, but I want to learn something for the future.

Өдрийн өмнө
Sean Hernandez
Sean Hernandez

I don’t even have a car,I think this is so cool

Өдрийн өмнө
Redline870
Redline870

The proper way to separate an upper control arm or ball joint is to hit the raised area of the knuckle right next to it. A few wacks with a hammer and it pops right out. Then you wont hammer the nut into the threads as well.

Өдрийн өмнө
Redline870
Redline870

MevoTech?!?! That stuff is the cheapest of the cheap! We used to use that crap at the shop I worked at and were warrantying parts all the damn time. Autozone's Duralast parts would be better than that junk! Other than that I loved the video though!

Өдрийн өмнө
Dallin Reed
Dallin Reed

How do you find what part to buy and we’re to buy them

Өдрийн өмнө
Devoid
Devoid

Everybody: make a video ChrisFix: Hey guys!

Өдрийн өмнө
Mod Cars Daily
Mod Cars Daily

What did he use to coat the wheel wells and steering knuckle? Looks like he used a brush with some what looks to be durable paint?

Өдрийн өмнө
ben stoltenberg
ben stoltenberg

Great vid! Glad i Subbed to this channel

Өдрийн өмнө
#Madesh Madesh
#Madesh Madesh

who watches this cause its satisfying but doesn't do anything.

Өдрийн өмнө
Daniel Rowell
Daniel Rowell

Hey Chris, I enjoyed your video, and you have a new subscriber. What paint did you use? As well as the silver paint? Looks great, and I want to use it on my trucks suspension.

2 өдрийн өмнө
Josh I.
Josh I.

Can you do a video on leaf springs?

2 өдрийн өмнө
Tom Tissier
Tom Tissier

Super boulot même si la barrière de la langue est un peu compliqué 👍

3 өдрийн өмнө
Alf
Alf

nice vid dude

3 өдрийн өмнө
Emilio Arredondo
Emilio Arredondo

So anyone know how to get the rest of that bearing off the hub at 16:10? Or just leave it on there and pretend it was never there?

3 өдрийн өмнө
Samuel Golden
Samuel Golden

This was incredibly satisfiying

3 өдрийн өмнө
Robloxian Bigtn12345
Robloxian Bigtn12345

How to replace trunk???? Mine is partly ripped off

3 өдрийн өмнө
coleswaggins
coleswaggins

Robloxian Bigtn12345 man, come on.

2 өдрийн өмнө
Jürgen Siefert
Jürgen Siefert

great tutorial, was very helpful for me and my honda 👍👍👍

3 өдрийн өмнө
Devesh Tewary
Devesh Tewary

8:48 the way the rust flies off is smooth...

3 өдрийн өмнө
Curious Betsy vlogs
Curious Betsy vlogs

Kind of ironic that I’m currently doing this on my skylark with 47 year old original suspension. If you think that’s bad I think half a century old original suspension is just a bit worse lol it was a challenge just to drive it normally

3 өдрийн өмнө
Doddy Cahyo Putra
Doddy Cahyo Putra

Neat and great work lads! Keep it up 👏

3 өдрийн өмнө
Mayur jani
Mayur jani

Great Vid informative as always. Just got to say they way iv always been taught when hammering or pushing out bearing \ bushes is to clamps or secure as close as possible to what your trying to remove. allowing the force to go where you want it with risking bending anything. just thought i would put that out there. Keep up the good work, you always keep your content interesting . :)

3 өдрийн өмнө
Hazshep24
Hazshep24

out with the old ( ͡° ͜ʖ ͡°) AND IN WITH THE NEW (ノಠ ͜ʖ ಠ) ノ

3 өдрийн өмнө
HK K
HK K

Very detailed and informative video. Great job!

4 өдрийн өмнө
Nero_Bacura77
Nero_Bacura77

Also you should find a fiero to play with.

4 өдрийн өмнө
Nero_Bacura77
Nero_Bacura77

Drift car or pro mod goo lol

4 өдрийн өмнө
Jonathan Gray
Jonathan Gray

I wonder if the haters can do 1/3 of what you can do Chris. A half means they will not. 3/4 means their lazy. Now all the haters can go to hell.

4 өдрийн өмнө
LIN HAO
LIN HAO

Love your sawing screws to flat heads method.

4 өдрийн өмнө
FPSKoda4
FPSKoda4

Does anyone wish that chrisfixes videos never end?

4 өдрийн өмнө
Fuson Yu
Fuson Yu

Dammmm I love your video to help me to learn those techniques. Thanks

4 өдрийн өмнө
Fred Garvin
Fred Garvin

You have 4.8M subs, don't you think you can rent some garage space and work out of the weather?

4 өдрийн өмнө
Rodrigo C C
Rodrigo C C

I remember this car when it came out... loving this honda series, and your videos are awsome. Made me want to buy a used truck pick-up and make usable in daily... 🤙🏻👏🏻🙌🏻

4 өдрийн өмнө
Christopher Gamer
Christopher Gamer

Chrisfix keep up the amazing good work and i can't wait to see the turbo kit install in the car.

4 өдрийн өмнө
ChrisFix
ChrisFix

Thanks a lot

4 өдрийн өмнө
Keith Sanders
Keith Sanders

Great video! I am pumped and ready to “fix it like Chris”!

4 өдрийн өмнө
ChrisFix
ChrisFix

Awesomeeee

4 өдрийн өмнө
OG Bandino
OG Bandino

Chris, would this tutorial still be relatively the same if my car is all wheel steering and all wheel drive? Or would there be too many differences

4 өдрийн өмнө
ChrisFix
ChrisFix

Basically the same. Actually since it’s all wheel drive and all wheel steering, the rear will be just like the front too!

4 өдрийн өмнө
Xanxツ
Xanxツ

remember to lubricate and penatrate properly

4 өдрийн өмнө
carter judkins
carter judkins

I really want to know if that’s actual black paint or something else cause it looks thicker than actual paint

4 өдрийн өмнө
Its Dudster
Its Dudster

Wheres the puberty at?

4 өдрийн өмнө
decoder55killer
decoder55killer

I nutted :v

4 өдрийн өмнө
H gamer lt
H gamer lt

9:08

4 өдрийн өмнө
KDM TRAP
KDM TRAP

Who would of thought somebody with marine Biology degree would make car videos

4 өдрийн өмнө
Марк Герасимов
Марк Герасимов

Just say that you like to cut rusty screws. Becuase if you are using pozidriv bit to unscrew phillips head you are effin idiot.

4 өдрийн өмнө
artdeco101010
artdeco101010

Thanks for posting this, very helpful to see how these should be done.

4 өдрийн өмнө
GROUCHY OLD MAN
GROUCHY OLD MAN

Prefer flat black in wheel well

4 өдрийн өмнө
Shepherd Wolf
Shepherd Wolf

Oh wow! I forgot about the ChrisFix decal on the valve cover! I need to go back to that video!

4 өдрийн өмнө
GROUCHY OLD MAN
GROUCHY OLD MAN

Q: Doesnt spraying off the wheel well introduce water into the trans via the missing axle inlet?

4 өдрийн өмнө
GROUCHY OLD MAN
GROUCHY OLD MAN

Stack your spare on top of the tire for better safety backup

4 өдрийн өмнө
Steve Huddleston
Steve Huddleston

@ChrisFix Which specific products did you use for the "silver rust paint" and the "thick black paint".

4 өдрийн өмнө
po123gsxr
po123gsxr

i was wondering the same thing. the link in the description gives several examples but didn’t seem like it was what he used

2 өдрийн өмнө
pipefighter
pipefighter

Nice video mr. !

4 өдрийн өмнө
Robert Brumley
Robert Brumley

Instead of going through all that crap, why not just buy a new car? Those old cars aren't worth anything no matter how much money you put into it, you will never get what you put into it.

4 өдрийн өмнө
ChrisFix
ChrisFix

I have less than $1k into the car including the price and it’s worth $1500. Plus they don’t make cars like this anymore and it’s a good vehicle to mess around with.

4 өдрийн өмнө
Luis Piedra
Luis Piedra

Can you give an estimate at how much it costs to replace the entire suspension with quality parts?

4 өдрийн өмнө
Luis Piedra
Luis Piedra

+ChrisFix well mine is a 2000 prelude which Is almost similar but just not sure which brand would be a good quality for that car that's not overpriced

3 өдрийн өмнө
ChrisFix
ChrisFix

You need to look it up for your specific car. It varies drastically

4 өдрийн өмнө
Supremium
Supremium

7:15 me beating my meat

4 өдрийн өмнө
alberto escamilla
alberto escamilla

i did not see any notification. great video, i was very excited and you make it seem soo easy

4 өдрийн өмнө
shoe112
shoe112

I have a very rusted 2001 nissan maxima, the hood dosnt latch because where the latch part would usually be attached to the frame, there iz now a hole of rust, is it worth saving or should i just start saving up for a newer car

4 өдрийн өмнө
Missy Darjan Spasojevic
Missy Darjan Spasojevic

Beautiful video great camera angles! you've came a long way since the older vids you definitely make a great instructive vid. I feel like my autistic son could watch this n do it 👌👏✌

4 өдрийн өмнө
Oscar Cabrera
Oscar Cabrera

Awesome video! You always have great content to tackle the job. 🔥

4 өдрийн өмнө
Dexter Tang
Dexter Tang

Another reason why those "philips" head screw striped may be due to the fact that they are JIS standard screw head. Similar in design to the common philips head but it inherently is less likely to round off like normal philips does if you use the right JIS screws. Little myth is that all "philips" head screw you see in cars are actually JIS screws. This will save you a lot of headache especially when such screws are used to hold the brake rotors in place.

4 өдрийн өмнө
Jesus Lopez
Jesus Lopez

The tire wear isn’t camber wear it’s toe wear. Camber would damage all the tire not just the one side unless your running +18 for that damage. Good video by the way!

4 өдрийн өмнө
bravo3
bravo3

Great stuff, and neat tricks......Thanks.

4 өдрийн өмнө
Lao Han Tun
Lao Han Tun

You guys open the bearing seal, the nylon seal, will find that, grease is so little, I would rub in real bearing grease, then close with nylon seal. I saw many cases like that.

4 өдрийн өмнө
Jorenz Tweet
Jorenz Tweet

Hi Chris. What do you think is the problem in my front suspension when I hear a sort of dribbling sound when passing by uneven road? Sound is not that audible on potholes.

4 өдрийн өмнө
MOON SHATER
MOON SHATER

7:15-7:17

4 өдрийн өмнө
Midnights & Mornings
Midnights & Mornings

Hey Chris, what school did you go to get your certification?

4 өдрийн өмнө
Joseph Fiumara
Joseph Fiumara

Love your videos Chrisfix! Watching your videos I'v learned a lot and saved hundreds of dollars, My neighbors and friends think i'm a mechanic ! hahaa ! Your a great teacher !

4 өдрийн өмнө
ghost GAMING
ghost GAMING

VanossGaming is that you 11:03

4 өдрийн өмнө
BDF martin
BDF martin

Criss that is a d16 right?

4 өдрийн өмнө
bibi
bibi

Pouvez vous mettre les sous-titres en français svp

4 өдрийн өмнө
Keyboard Dancers
Keyboard Dancers

Old tech is environmentally friendly, creates jobs and prevents drug use.

4 өдрийн өмнө
Nixy Guyaban
Nixy Guyaban

7:06 ChrisFix: You're probably gonna do this a bunch of times. 🤣

5 өдрийн өмнө
Greystoke1986
Greystoke1986

Chris, I have enjoyed watching everything that you are doing to the Del Sol!!! What do you have planned for the exterior? Is it a secret or can you reveal a few hints now? Great job Chris!!!

5 өдрийн өмнө
Jesse Renn
Jesse Renn

Whoa wait when did he repaint the engine bay? Or was it always that white?

5 өдрийн өмнө
Sly John
Sly John

what part of the car are you resting on the jack stands in the beginning?

5 өдрийн өмнө
Abdulazeez Jawad
Abdulazeez Jawad

7:05 - when your parents go out for groceries and you're home alone

5 өдрийн өмнө
BooMan TheGhost
BooMan TheGhost

7:03 OH YEAH DADDY WORK THE SHAFT!!!

5 өдрийн өмнө
KEE LOE
KEE LOE

Great vid. . . . Still dont have the balls to try it myself.

5 өдрийн өмнө
Bedlamco
Bedlamco

What is that silver paint

5 өдрийн өмнө
JillyBean860
JillyBean860

This brought back awful/great memories of my front suspension rebuild. I did this years ago with the help of your past YouTube videos and everything came out great. You are such an inspiration!

5 өдрийн өмнө
jamesws3
jamesws3

What penetrating oil have you found to work best? Reviews are all over the place.

5 өдрийн өмнө
TheRustyCracker
TheRustyCracker

Has a cordless impact.... nice tools... but uses a hand saw lol.

5 өдрийн өмнө
Chad Bell
Chad Bell

They have a tie rod end remover that makes it much easier to remove the inner tie rod. I would suggest this method over the way ChrisFix does it.

5 өдрийн өмнө
Fury_LitBoy
Fury_LitBoy

Why are there even dislikes on this amazing video ❤❤ Love your content

5 өдрийн өмнө
Marcelo Esquivel
Marcelo Esquivel

Buy a silverado plzzzzz

5 өдрийн өмнө
Jonny DIY
Jonny DIY

May have been answered already but what kind of Paints were those at the end? Silver was? Never seen silver rust proofing paint. Black was Herculiner type paint or?

5 өдрийн өмнө
Jonny DIY
Jonny DIY

Por15? 😁

5 өдрийн өмнө
Haxmaster
Haxmaster

7:04 Me every night before bed except dealing with another "Hub"

5 өдрийн өмнө
decco
decco

chris is obviously a child of god. id have that hub off in 4 pumps

2 өдрийн өмнө

Дараах

How to Replace a Clutch in your Car or Truck (Full DIY Guide)

32:00

Is Kanye’s Coachella Church Merch Too Much?

4:40

Is Kanye’s Coachella Church Merch Too Much?

The Real Daytime

Үзсэн тоо 287 179

Amazing Machines operating at an INSANE LEVEL ▶7

15:26

Amazing Machines operating at an INSANE LEVEL ▶7

Freeze Lists

Үзсэн тоо 691 000

How to Strip a Car COMPLETELY

14:56

How to Strip a Car COMPLETELY

ChrisFix

Үзсэн тоо 5 500 000

5 Cars That Won’t Last 100,000 Miles

09:01

5 Cars That Won’t Last 100,000 Miles

Scotty Kilmer

Үзсэн тоо 698 000

BMW 7  Full repair. Полный ремонт.

20:02

BMW 7 Full repair. Полный ремонт.

Arthur tussik

Үзсэн тоо 7 200 000

How to SUPER CLEAN your Engine Bay

21:59

How to SUPER CLEAN your Engine Bay

ChrisFix

Үзсэн тоо 23 000 000

Welcome to the Sunshine State. Sailing in FLORIDA! ☀️⛵️ Ep.194

14:34

answering your assumptions about me... (THE TRUTH)

37:24

answering your assumptions about me... (THE TRUTH)

The DDG Family

Үзсэн тоо 316 391

You've Never Seen This Before!!

23:58

You've Never Seen This Before!!

Roman Atwood Vlogs

Үзсэн тоо 1 144 770

Garage Built Supra! 2jz no shhhhhhh..

25:24

Garage Built Supra! 2jz no shhhhhhh..

PFI Speed

Үзсэн тоо 40 995

ULTIMATE Electric Drift Trike

6:20

ULTIMATE Electric Drift Trike

colinfurze

Үзсэн тоо 996 499

1990 Nissan Skyline R32 GTR: Regular Car Reviews

9:28

1990 Nissan Skyline R32 GTR: Regular Car Reviews

RegularCars

Үзсэн тоо 257 121

1985 Renault R5 Turbo2 - Jay Leno’s Garage

27:45

1985 Renault R5 Turbo2 - Jay Leno’s Garage

Jay Leno's Garage

Үзсэн тоо 293 685

The War on Bird Scooters

17:07

The War on Bird Scooters

Eddy Burback

Үзсэн тоо 142 037